View This Issue - February 2009

LED DESIGN FORUM: Avoiding thermal runaway when driving multiple LED strings (MAGAZINE)

An increasingly common method of increasing the light output from a high power LED cluster is to run parallel strings of LEDs from a single constant current source. But this option is not without its hazards.

A typical high power 350mA white LED has a forward voltage (Vf) of about 3.3V, so if an cluster of 10 LEDs were required in an application, connecting of the LEDs all in series would require a driver capable of delivering at least 33V. If the supply voltage is 24VDC, then an expensive boost converter would be required with all the attendant EMC problems it creates.

Fig. 1
Fig. 1. Driving multiple LED strings
Connecting the LEDs as two strings of five wired in parallel requires a higher current 700mA constant current source but only 16.5V output voltage. Thus a low cost buck converter running from 24VDC can be used. The circuit (similar to that shown in Fig. 1) can be found in many manufacturers’ datasheets.

The basic assumption made with this circuit suggestion is that the 700mA regulated current from the LED driver will be shared approximately evenly across both strings of LEDs, i.e. each string of LEDs will see 350mA of current. However, this is rarely the case.

How LEDs become overdriven
Even if the LEDs are all from the same production batch and sequentially manufactured, the Vf of individual LEDs still has a ±20% tolerance. The tolerances mean that the total forward voltage for each string can be very different and therefore the current mismatch significant (see Fig. 2).

Fig. 2
Fig. 2. Real life situation
In a test using identical SMD LEDs from a single production batch and using 1 Ohm resistors to help balance out the forward voltages, the currents flowing in each string were measured to be 306mA and 394mA. The LED driver was still doing its job of correctly limiting the current to 700mA, but the over‐current flowing through the second string was seriously overdriving the LEDs.

Worse, as the LEDs started to get warm, the combined forward voltage of the higher current string started to decrease. This increased the imbalance and more current started to flow through the already over‐driven string. The current through the other string of LEDs reduced as the constant current driver compensated, so they started to cool down and their forward voltage increased.

The net result was thermal runaway with the majority of current flowing through one string only, even though the LEDs were mounted on a large metal heat sink. The test was stopped when the current imbalance was 600mA to 100mA. Obviously, if this situation was allowed to continue, the over‐driven string would eventually fail and then the entire 700mA would flow through the remaining intact string and destroy that as well.

And this circuit is often given as a recommended application example!

Using a current mirror
What is required is a way of balancing the currents flowing through the two strings to ensure that they remain approximately equal, even if the combined forward voltages are mismatched. The balancing circuit must also continually compensate for changes in forward voltage caused by changes in the operating temperature and by aging of the LEDs.

Fortunately, there is a very simple transistor circuit that will do this job admirably. It is called a current mirror and “reflects” the current flowing through one reference transistor onto the current flowing through a second transistor (see Fig. 3). As long as the transistors are reasonably well matched in terms of their Vbe values, the currents will also be reasonably well matched.

Fig. 3
Fig. 3. Using a current mirror

In tests using Recom’s 700mA LED driver and two strings of 350mA Osram LEDs, the currents flowing through the two strings were matched to an accuracy of about 87% over the entire input voltage range of the driver from 16VDC to 36VDC. The LED currents were stable as the LEDs warmed up and no thermal runaway was observed. It is important that the two transistors are both at the same temperature so a copper clamp was used to thermally connect both transistors together to keep their Vbe voltages stable.

In addition, if any of the LEDs in String 1 fail, the current to ALL of the LEDs is disconnected. Thus the LEDs on String 2 are automatically protected against being over‐driven.

However, this circuit is still not ideal. The currents are not perfectly matched and if any of the LEDs in String 2 fail, then all of the 700mA source current will still flow through the first string and destroy it.

Over-current protection
Fig. 4 shows the final version of the current balancing circuit. The addition of 1.5 Ohm resistors in the emitter paths makes the circuit less sensitive to small Vbe changes and balances the currents in the two strings to 99% accuracy.

Fig. 4
Fig. 4. Over‐current protection

The addition of a small signal transistor as a current monitor protects the LEDs from being overdriven in the case of any LED failures. If LED1‐LED5 fail open circuit, then the current in the second string falls to zero as before. However, if LED6–LED10 fail, then the current increases in the first string until the voltage developed across the 1.5 Ohm emitter resistor reaches around 0.7V, thus turning on the BC337 transistor and pulling the base voltage of the power transistor to ground and limiting the current. With the component values given in the circuit, the measured current limit was 445mA with String 2 open circuit.

The circuit suggestion given in Fig. 4 can theoretically be extended to any number of LED strings by adding an NPN transistor and emitter resistor to each additional string and tying the transistor bases together. The current flowing through the reference transistor will be faithfully mirrored by all of the other transistors.

However, considering that LEDs are high reliability illumination sources and the driver and associated components need to be equally reliable to get the maximum lifetime out of the system, it is recommended that the circuitry be kept as simple as possible and restricted to only one or two strings per driver.

RELATED COMPANIES

Zierick Manufacturing Corp

Offers innovative solutions for interconnect applications. Specializes in wire-to-board and board-to-board applications. Provides surface mount and thru-hole products while further reduci...

Cree Inc

Leads the LED industry in performance, brightness and reliability with its XLamp LED family, enabling the lighting industry with efficient, environmentally-friendly LEDs that produce beau...

InnoLight sp zoo

EU located lighting manufacturer for LED GU10 5W 600lm CRI>80 reflector, great performance, and LED E27 5W 380lm classic traditional appearance.

CSA Group

A global solutions provider of product testing and certification services for electrical, mechanical, plumbing, gas, medical and a variety of other products.

Energy Efficient Lighting

Energy Efficient Lighting offers total solutions to both conventional and more advanced LED lighting fixtures and LED retrofit kits for commercial and industrial applications.

Schréder

48 companies worldwide, passionate about light and innovation, experts in developing LED lighting solutions for safe and comfortable environments with significant energy and cost savings,...

Guardian Industries

Guardian Industries Corp. is a leader in float glass, fabricated glass and high performance coated glass products. Guardian lighting solutions deliver optimal performance, flexibility and...

ELMA Electronic Inc

Provides standard and customized LED solutions. Elma's LED family offers consistent, reliable, and durable illuminating and indicating solutions.

LEDSAmerica Inc

LedsAmerica is a full line LED line company and has manufacturing in Iowa where T8 LED-O tubes and street lights are made together with PL, PARs, High Bay lights. MAx

Lumentra Inc

Provides NVLAP accredited optical (photometry, colorimetry, Lumen maintenance), thermal (mapping and transient analysis), electrical characterization services, product development, supply...

CINCON USA

The LED, DC-DC and AC-DC power supplies from 1W - 1600W. Cincon’s lighting controllers, interfaces and devices incorporating DALI protocol. LED drivers from 25W - 150W with international ...

LTF LLC

LTF, LLC is a U.S based solid-state lighting product development and manufacturing company with facilities located in both USA and China.

Marian Inc

Marian is a global company who supplies die cut and converted parts to the LED market. Materials include thermal pads, reflective, venting, gaskets, insulators, diffusers and more.

Colorimetry Research

Specializes in the field of optics, manufacturing, electronics and software enables us engineer products with the right balance of hardware and software.

eldoLED America Inc

Designs and manufactures drive solutions for LED based lighting systems. Our technologies empower our customers to deliver the promise of LED lighting.

Cirrus Logic Inc

Cirrus Logic develops high-precision, analog and mixed-signal integrated circuits for a broad range of innovative customers across a variety of energy-related applications, including the ...

LEDSupply

Established in 2002 as an ecommerce store for all your LED product needs.

CINCON

Designer and manufacturer of custom and industry standard LED, DC-DC and AC-DC power supplies from 1W to 1600W. Cincon also designs and manufacturers lighting controllers, interfaces...

Illumination Machines

Illumination Machines designs custom optics, heat sinks, and remote phosphor systems for LED luminaires and lamps.

eldoLED BV

eldoLED is a world leader in the design and manufacture of intelligent drive solutions for LED based lighting systems. Our technologies empower our customers to deliver the promise of LED...

RELATED PRODUCTS

Cree XLamp® XP-L LEDs-the industry’s highest efficacy single-die LED.

Cree® XP-L LED is the first commercially available single-die LED to achieve up to 200LPW at 350mA. The XP-L enables 50% or more performance increase as a drop-in upgrade.

Surface Mount Wire Gripper - Part Number 1301

The Zierick 1301 is designed to allow customers to easier terminate a stripped wire to a PCB. Wire sizes to 24 AWG. Terminal is UL Recognized.

Surface Mount Wire Gripper - Part Number 1262

The Zierick 1262 is designed to allow customers to easier terminate a stripped wire to a PCB. Wire sizes from 0.025" to 0.095". Terminal is UL Recognized.

Unlock new LED lighting solutions with Cree High Density LEDs

Cree® High Density LEDs deliver the industry’s highest optical control factor enabling lighting manufacturers to improve performance, cost and size of LED lighting—enabling never before p...

Cree CXA LED Array Family

Cree’s CXA LED Arrays are optimized to simplify design and lower system cost, delivering high lumen output and efficacy with a family of single, easy-to-use arrays.

Cree LED Modules

Cree LED modules deliver beautiful, consistent light, backed by a 5-year warranty. They offer a choice of dimming options, while reducing the lighting power load by 80%.

Cree XLamp® XM-L2 EasyWhite® LED

The first 5mmx5mm LED to enable color-consistent 50W halogen performance; the XM-L2 EasyWhite delivers 1,100 lumens and is optimized to replace halogen technology.

Surface Mount Insulation Piercing Terminals

Surface Mount Wire-to-Board terminals available for wire gauges ranging from 24 to 14 AWG. Parts can be terminated to allow daisy-chain applications. Eliminates difficulty with direct...

P3 Indoor Full Color LED Display Video screen

High-density pixel pitch,high resolution,high refresh rate,magnificent and high-definition image and video effect.P3,P5,P6,P7.62 to P10 available.Epistar SMD LED,wide viewing angle.High r...

LED Panel Light

Designed to replace T8 fluorescent tube or Phillip Grille light.Epistar 3528/3014 SMD LED.Aluminum alloy body.Even and Soft light beam.Various mounting means.50,000 hours lifetime.Environ...

Rotatable LED Down Light, beam angle adjustable 10-60°

Beam angle adjustable 10-60 degree.Shell can rotate 360°,vertical 0-40°.High power CREE LED,even and uniform light output,Die casting aluminum alloy housing,good heat sinking.Widely used ...

Solar LED Paver Light

100% solor powered.No wires, no electricians.Super capacitors instead of battery,maintenance-free.Absorb sunlight in daytime and illuminate 8-12 hours during night. Epistar LED.Activation...

T8 LED tube light

Epistar Super bright 3528/2835 SMD LED.Aluminum alloy body with plastic cover.Consist with traditional fluorescent tubes.Easy mounting.PF>0.90,CRI>72,Over 60% energy-saving,Low degradatio...

LED light Bulb – LED spotlight

The AR111,GU10,MR16,PAR30,PAR38 LED bulbs are ideal replacement of 10-75W halogen or CFL bulbs.Cree/Everlight LEDs.PMMA lens.Aluminum housing.Good heat dissipation.Surface temperature les...

Super bright Injection LED modules

Housed by ABS material,covered by epoxy resin on surface with good insulation.Beautiful appearance.Waterproof.Anti-fire.Super bright 5050/3528 LED.12V voltage.Ideal light source for backl...

Flexible LED screen - Rental and Stage LED billboard

Special design,flexible use,light weight,super slim,transparent,SMD technology,easy to install.Can realize any curved and creative installation horizontally and vertically.IP65 protection...

LED flexible strip and aluminum LED bar

Full range of LED strip and bar including the unique high lumen strip. Protection degree up to IP68.Epistar 3528/5050 SMD LED.Compliant with CE & RoHS.2-year warranty.3528: 60LED/m,120LED...

iVAR COB LED Downlight

iVAR COB LED Downlight use die-casting magnesium alloy to make the main body,has Excellent heat dissipation performance,and Unique and delicate looking design.

LIMS - Liquid Injection Molding System

Silicone LIMS can be used to injection mold silicone components such as lenses or gaskets in an automated process. The two-component, thermoset material ranges in Shore A hardness from 5-80.

360 degree 10W led bulb

360 degree 10W led bulb has high efficiency, high power factor,environmental friendly, unique heat-dissipating design and perfect thermal management.

TOPIC INDEX

CONNECT WITH US

                

SOCIAL ACTIVITY

UPCOMING EVENTS

  • List View

NEWSLETTERS

LEDs Magazine Newsletter

Our weekly flagship news source
SUBSCRIBE

Product Focus

Monthly newsletter
SUBSCRIBE

Illumination in Focus

Bi-monthly newsletter
SUBSCRIBE

  •  
  •  
  •  
Copyright © 2007-2014. PennWell Corporation, Tulsa, OK. All Rights Reserved.